Dolphin's JITs have a minor terminology problem: The term "fastmem" can
refer to either the system of switching between a fast path and a slow
path using backpatching, or to the fast path itself. To hopefully make
things clearer, I'm adding some new terms, defining the old and new
terms as follows:
Fastmem: The system of switching from a fast path to a slow path by
backpatching when an invalid memory access occurs.
Fast access: A code path that accesses guest memory without calling C++
code.
Slow access: A code path that accesses guest memory by calling C++ code.
With this, situations where multiple arguments need to be moved
from multiple registers become easy to handle, and we also get
compile-time checking that the number of arguments is correct.
At the end of each frame automatically update the Current Value for
visible table rows in the selected and visible CheatSearchWidget (if
any). Also update all Current Values in all CheatSearchWidgets when the
State changes to Paused.
Only updating visible table rows serves to minimize the performance cost
of this feature. If the user scrolls to an un-updated cell it will
promptly be updated by either the next VIEndFieldEvent or the State
transitioning to Paused.
If dcache is enabled when the game starts, initializing the fastmem
arena is still useful in case the user changes the dcache setting.
And initializing it doesn't really cost anything.
Preparation for the next commit.
JitArm64 has been conflating these two flags. Most of the stuff that's
been guarded by fastmem_arena checks in fact requires fastmem.
When we have fastmem_arena without fastmem, it would be possible to do
things a bit more efficiently than what this commit does, but it's
non-trivial and therefore I will leave it out of this PR. With this
commit, we effectively have the same behavior as before this PR - plus
the added ability to toggle fastmem with a cache clear.
This is needed so that the checks added in the previous commit will be
reevaluated if the value of m_enable_dcache changes.
JitArm64 was already recompiling its asm routines on cache clear by
necessity. It doesn't have the same setup as Jit64 where the asm
routines are in a separate region, so clearing the JitArm64 cache
results in the asm routines being cleared too.
Some code paths in EmuCodeBlock.cpp that were checking fastmem_arena
should really also be checking m_enable_dcache.
Because JitArm64 centralizes more or less all memory access to the
EmitBackpatchRoutine function and because that function already
contained a check, JitArm64 works fine without the additional checks
added by this commit. Regardless, I added the checks to MMU.cpp instead
of EmuCodeBlock.cpp where applicable so they would be available to
JitArm64. Maybe one day JitArm64 will need them if its code gets
restructured.
The table only needs to be recreated when the displayed addresses might
change. If we're just refreshing the current values then update those
table cells and leave the rest of the table alone.
The code previously did this indirectly via `std::map<double, int>`, the key being the timestamp, which required a questionable workaround for the case where multiple states have the same timestamp. By having a particular combination of timestamps in the on-disk savestates, you could cause this workaround to infinitely loop, locking up Dolphin. This avoids this completely by refactoring the logic and just using `std::vector` instead.
Since ccf92a3e56, recording fifologs multiple times after launching dolphin caused all initial state to not be saved (the initial contents of bpmem, cpmem, etc were all zeroed out). For some games, this was not noticeable, as most registers were set each frame, but for others, this resulted in completely broken fifologs. (Note that recording fifologs also required 05181f6b88 and 9e0755a598 to be cherry-picked due to other, since fixed, regressions.)
This was because previously, `Renderer::CheckFifoRecording` was called every frame, but ccf92a3e56 changed it into a callback (`m_end_of_frame_event`) that was removed when recording ended. Thus, before, `OpcodeDecoder::g_record_fifo_data = IsRecording()` was called when `IsRecording()` returned false, but after that commit `g_record_fifo_data` never got changed back to false, so the check for `was_recording` only ever passed on the first fifolog recorded (even after stopping and starting a game).
There may still be another issue lurking, as I'm not sure if all broken fifologs were caused by recording multiple fifologs (for instance, on https://bugs.dolphin-emu.org/issues/13377, only one fifolog was initially uploaded, but it was affected by an issue with the same symptoms as this).
