The swaps are confusing and don't accomplish much.
It was originally written like this:
u32 pte = bswap(*(u32*)&base_mem[pteg_addr]);
then bswap was changed to Common::swap32, and then the array access
was replaced with Memory::Read_U32, leading to the useless swaps.
While 6xx_pem.pdf §7.6.1.1 mentions that the number of trailing
zeros in HTABORG must be equal to the number of trailing ones
in the mask (i.e. HTABORG must be properly aligned), this is actually
not a hard requirement. Real hardware will just OR the base address
anyway. Ignoring SDR changes would lead to incorrect emulation.
Logging a warning instead of dropping the SDR update silently is a
saner behaviour.
debaf63fe8 moved the "Sonic epsilon hack"
to vertex shaders. However, it was only done for targets with depth
clamping. If this is not available, for example the target is OpenGL ES,
the Sonic problem appears (https://bugs.dolphin-emu.org/issues/11897).
A version of the "Sonic epsilon hack" is added for targets without
depth clamping.
This changes FileSystemProxy::Open to return a file descriptor wrapper
that will ensure the FD is closed when it goes out of scope.
By using such a wrapper we make it more difficult to forget to close
file descriptors.
This fixes a leak in ReadBootContent. I should have added such a class
from the beginning... In practice, I don't think this would have caused
any obvious issue because ReadBootContent is only called after an IOS
relaunch -- which clears all FDs -- and most titles do not get close
to the FD limit.
JitArm64::DoJit contains a check where it prints a warning and tries
to pause emulation if instructed to compile code at address 0. I'm
assuming this was done in order to provide a nicer error behavior
in cases where PC was accidentally set to null. Unfortunately, it
has started causing us problems recently, as 688bd61 writes and runs
some code at address 0 to simulate the PPC being held in reset.
What makes this worse is that calling Core::SetState from the CPU
thread is actually not allowed and will cause a deadlock instead of
the intended behavior. I don't believe there is anything on a real
console that would stop you from executing code at address 0 (as
long as the MMU has been set up to allow it), and Jit64::DoJit
doesn't contain any check like this, so let's remove the check.
This commit adds a new "discarded" state for registers.
Discarding a register is like flushing it, but without
actually writing its value back to memory. We can discard
a register only when it is guaranteed that no instruction
will read from the register before it is next written to.
Discarding reduces the register pressure a little, and can
also let us skip a few flushes on interpreter fallbacks.
The output of instructions like fabsx and ps_sel is store-safe
if and only if the relevant inputs are. The old code was always
marking the output as store-safe if the output was a single,
and never otherwise.
Also, the old code was treating the output of psq_l/psq_lu as
store-safe, which seems incorrect (if dequantization is disabled).
This improves the speed of verifying Wii WIA/RVZ files.
For me, the verification speed for LZMA2-compressed files
has gone from 11-12 MiB/s to 13-14 MiB/s.
One thing VolumeVerifier does to achieve parallelism is to
compute hashes for one chunk of data while reading the next
chunk of data. In master, when reading data from a Wii
partition, each such chunk is 32 KiB. This is normally fine,
but with WIA and RVZ it leads to rather lopsided read times
(without the compute times being lopsided): The first 32 KiB
of each 2 MiB takes a long time to read, and the remaining
part of the 2 MiB can be read nearly instantly. (The WIA/RVZ
code has to read the entire 2 MiB in order to compute hashes
which appear at the beginning of the 2 MiB, and then caches
the result afterwards.) This leads to us at times not doing
much reading and at other times not doing much computation.
To improve this, this change makes us use 2 MiB chunks
instead of 32 KiB chunks when reading from Wii partitions.
(block = 32 KiB, group = 2 MiB)
This can't actually happen in practice due to how WAD files work,
but it's very easy to add support for thanks to the last commit,
so we might as well add support for it.
The performance gains of doing this aren't too important since you
normally wouldn't run into any disc image that has overlapping blocks
(which by extension means overlapping partitions), but this change also
lets us get rid of things like VolumeVerifier's mutex that used to
exist just for the sake of handling overlapping blocks.
Panic alerts in DiscIO can potentially be very annoying since
large amounts of them can pop up when loading the game list
if you have some particularly weird files in your game list.
This was a much bigger problem back in 5.0 with its
"Tried to decrypt data from a non-Wii volume" panic alert, but
I figured I would take it all the way and remove the remaining
panic alerts that can show up when loading the game list.
I have exempted uses of ASSERT/ASSERT_MSG since they indicate
a bug in Dolphin rather than a malformed file.
If we know at compile time that the PPC carry flag definitely
has a certain value, we can bake that value into the emitted code
and skip having to read from PPCState.
